Concrete Slab Calculator

Updated November 18, 2026 · Free to use · How we calculate

Quick answer: a slab that is 4 inches thick needs 1 cubic yard of concrete for every 81 square feet. Multiply length by width to get the area, divide by 81, then add about 10% for waste.

Concrete slab calculator

Tap a common thickness below
5-10% is typical for flat, well-formed work
Leave blank to skip the cost estimate

Material estimate only. Delivery, pumping, taxes, labour, base material and reinforcement are not included.

How to use the slab calculator

  1. Enter the length and width of the finished slab.
  2. Enter the thickness, or tap a common size. Four inches is common for walkways and patios, while garage floors and driveways are often thicker.
  3. Keep the waste at 10% unless your ground is very flat and the forms are tight.
  4. Optionally type your supplier price per cubic yard to see a rough material cost.
Length (L)Width (W)Thickness (T) Volume = L × W × T
Convert all three measurements to feet, multiply, then divide by 27 to get cubic yards.

How many square feet does a cubic yard cover?

A cubic yard is 27 cubic feet. Divide that by the thickness in feet and you get the area one yard will cover. This table saves you doing the sum every time.

Slab thicknessArea covered by 1 cubic yard
3 in108 sq ft
4 in81 sq ft
5 in64.8 sq ft
6 in54 sq ft
8 in40.5 sq ft

Cubic yards needed for common slab sizes

These figures are the exact volume before any waste allowance.

Slab size4 in thick6 in thick
10 ft × 10 ft1.23 yd³1.85 yd³
12 ft × 12 ft1.78 yd³2.67 yd³
12 ft × 20 ft2.96 yd³4.44 yd³
20 ft × 20 ft4.94 yd³7.41 yd³
24 ft × 24 ft7.11 yd³10.67 yd³

For example, a 20 × 20 ft slab at 4 inches is 4.94 cubic yards. With 10% extra you would order about 5.4 cubic yards, which most suppliers will round to 5.5.

How thick should a concrete slab be?

Thickness depends on the load and local requirements. These are common starting points, not engineering advice:

  • Walkways, patios and shed bases: often 4 inches.
  • Garage floors: commonly 4 to 6 inches.
  • Driveways for regular cars: commonly 4 to 6 inches; heavier vehicles need more.

Soil type, climate, reinforcement and building codes can all change the requirement. If the slab carries a building or heavy equipment, ask a structural engineer or your local building department.

Planning tips that affect the quantity

  • Subgrade matters. A compacted, level base keeps the slab at an even thickness. Low spots soak up extra concrete.
  • Measure the finished size. Include the full area, including any thickened edges, which you can add as a separate calculation.
  • Reinforcement. If your plan calls for rebar, use the general concrete calculator for the volume and plan the steel separately.
  • Weather and finishing time. Order a delivery window you can actually finish within. Waiting does not change the volume but it can change your results.

Frequently asked questions

How many cubic yards do I need for a 10x10 slab?

A 10 ft by 10 ft slab needs 1.23 cubic yards at 4 inches thick and 1.85 cubic yards at 6 inches thick, before waste. With 10% extra, that is about 1.36 and 2.04 cubic yards.

How many square feet does 1 yard of concrete cover?

At 4 inches thick, one cubic yard covers 81 square feet. At 6 inches it covers 54 square feet, and at 3 inches it covers 108 square feet.

How much concrete do I need for a 20x20 slab?

A 20 ft by 20 ft slab at 4 inches thick needs 4.94 cubic yards, or about 5.4 cubic yards with 10% waste. At 6 inches it needs 7.41 cubic yards before waste.

How thick should a concrete slab be?

Four inches is common for walkways and patios, and 4 to 6 inches for garage floors and driveways. Always check local code and soil conditions, and ask a professional for structural slabs.

Does the cost estimate include delivery?

No. It multiplies the cubic yards by the price you enter. Delivery, short-load fees, pumping, taxes, labour, base material and reinforcement are extra.

Related tools and guides